Trailair Pin Box Replacement For A Lippert Rhino Pin Box

Question

Question:

Do you have in stock a 21000 trailaire to replace a rhinobox on a 2021 Cedar Creek 5th wheel?

asked by: Whit

0

Expert Reply:

The Trailair Flex Air 5th Wheel Pin Box - Lippert Rhino - 21,000lbs Item # LC65VR is exactly what you're looking for to replace your Lippert Rhino pin box.

expert reply by: Kevin C

0

Answer 1

Hi Michael, Yes, the Trailair Air Ride 5th Wheel King Pin #UF35-946219 can be used with a Demco Autoslide hitch like the #DM6077, you'll just need to swap out the capture plates on the hitch with part #DM6171 to fit the Trailair pin box. I do…

view full answer...

Answer 2

Hey Pat, The Rhino box definitely is shorter than what most Rver's were hoping for so we get this question all the time. Switching to a MORryde Cushioned pin box designed with a Rhino box bolt pattern unfortunately won't give you extra…

view full answer...

Answer 3

You can absolutely use a sliding hitch with the Trailair Flex Air 5th Wheel Pin Box #LC369535 to replace your Lippert 1621 pin box. This will work wonderfully with a sliding 5th wheel hitch to give you the most comfortable towing experience possible.…

view full answer...

Answer 4

My recommendation to replace a RhinoBox is to use the Curt Flex Air 5th Wheel Pin Box, #LC65VR. This is designed to replace a Lippert Rhino Box 21K Pin Box. (Curt, and TrailAir are both owned by Lippert, this is the same product as a Lippert TrailAir…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Trailair Pin Box Replacement For A Lippert Rhino Pin Box

Product Page this Question was Asked From

Continue Researching