Membrane Dimensions On LaSalle Bristol RV Roof Replacement Kit

Question

Question:

The length of my roof that’s needs replaced is 24 ft. Would the 25 ft kit be enough?

asked by: Richard M

0

Expert Reply:

The membrane included in the LaSalle Bristol RV Roof Replacement Kit w/ XTRM Membrane - 25' Long Item # 344270KIT25 measures 25' x 9-1/2'. So as long as your roof falls at or under 9-1/2' in width you should just have an extra foot in length to trim off.

expert reply by: Kevin C

0

Answer 1

Hey Kim, The thickness of the LaSalle Bristol XTRM PVC Membrane in the #344270KIT21 kit is 27 mils, or 0.027" thick. The membrane itself has a 15 year warranty that is handled by LaSalle Bristol directly! What kind of trailer are you wanting to…

view full answer...

Answer 2

Hey Vicki! To replace your RV's roof you'll need a replacement kit like the LaSalle Bristol RV Roof Replacement Kit w/ XTRM Membrane item #344270KIT30. This ones for a 30' RV but we've got quite a few size options. This installation…

view full answer...

Answer 3

Hello Mike, thanks for reaching out. We do offer roof replacement kits like the #344270KIT25 you were looking at. This comes with everything needed to replace the roof membrane including adhesive, butyl tape, membrane and sealant. The membrane itself…

view full answer...

Answer 4

The LaSalle Bristol RV Roof Repair Kit #344270KIT30 uses the 30 foot long membrane roll- part #3441700534142711430, which is 9-1/2 feet wide. If your roof is 9'-6", then this will be the exact width of the roll.

view full answer...

Answer 5

Hi Rick, LaSalle Bristol's roof membrane is made of PVC which is known to be durable and offer better protection against punctures and overall weathering. Alpha Systems offers TPO roof membranes that are more environmentally friendly/recyclable…

view full answer...

Answer 6

The 1988 Layton travel trailer nearest the 17-foot size you mentioned is their 16-foot model M-1661. The adhesive included in the etrailer kit #344270KITW is not suitable for use on the rubber roof on your trailer. However we do offer part #0160297,…

view full answer...

Answer 7

Take a look at the picture I have included. You can see that the cable is secured to the valve using a set screw. So you would loosen that, pull out the old cable, put in the new one, and tighten the set screw back down. If your valve is set up the…

view full answer...

Answer 8

Unfortunately we don't have specifications like how far the pipe is from the edge of your travel trailer. But the LaSalle Bristol Cable-Actuated RV Waste Valve #34466N11AB36GM is designed to replace the waste valve from your travel trailers…

view full answer...

Answer 9

The best way to select the correct size vinyl trim insert is to measure the trim insert you have now while flat, not the track. We don't really recommend measuring the track as they are not all a standard width. That said, we only offer vinyl…

view full answer...

Answer 10

When replacing your vinyl molding trim you should measure the overall width of the trim. Since yours is 7/8" I recommend going with the 1" trim, and here are the available options in either White or Black: - 25 Feet: White #37210025 or…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...