Replacement Guide On for CE Smith Guide On # CE27620

Question

Question:

We lost/stolen one of our CE27620 40 inch guides. We have the clamps but need only ONE guide. Do we have to buy a pair or can we just the guide?

asked by: David B

0

Expert Reply:

To replace just one of the guide ons of the # CE27620 you'd need the part # CE27608PG for the bracket, part # CE11339 for the PVC pipe, and then for the cap part # CE11331-DRILLED and you'd be set.

expert reply by: Jameson C

0

Answer 1

There is an upright which may work for you, the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - Lanced - 39" #CE27605PG. This upright has a bottom leg of 23 inches, and is a replacement for CE Smith Post-Style Guide-Ons…

view full answer...

Answer 2

I reached out to CE Smith about the #CE27620 and although they do have a no-rotate notch there’s no need for the tubes to lock once they are put down on the galvanized tube since they are snug and tight. The PVC tubes are not made to rotate. If they…

view full answer...

Answer 3

The most room you can get with the CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 is right at 11" so you'll need the 60" long guide-on kit #CE27640 instead which is about 6" longer and will give you more then enough…

view full answer...

Answer 4

Yes, if you ordered the CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 and then found that the PVC seemed too short you could replace just the PVC with a longer section of pipe as long as the diameter matches.

view full answer...

Answer 5

If your trailer frame is up to 3" wide x 4-1/4" tall the Guide Ons part #CE27620 would fit as-is on your trailer. For frames up to 5-1/4" tall, 2 extra-long U-bolt kits #CE11416 ( sold separately) are required. You will need to…

view full answer...

Answer 6

It sounds like you'll need to do some fab work in order to get the guide-ons to work. I believe your best bet would be to eliminate the u-bolts and have the brackets welded to the top or the underside of the frame member. If the fender step…

view full answer...

Answer 7

In regards to the CE Smith Post-Style Guide-Ons #CE27620, the square tube that attaches to the trailer is a 1-1/2" x 1-1/2" square.

view full answer...

Answer 8

From the top of the frame that the CE Smith Post-Style Guide-Ons #CE27620 install to the top of the PVC measures 40" as you can see in the attached photo. If these aren't the correct height for you I have also linked our selection of…

view full answer...

Answer 9

The CE Smith Post-Style Guide-Ons for Boat Trailers - 60" Tall - Black - 1 Pair #CE27646 will give you a 90 degree angle. The similar white #CE27640 with the 60 inch height will give you close to that angle but not quite as precise angling out a…

view full answer...

Answer 10

The guide-ons you choose for your boat and trailer really depends on the height of your boat. For a low-profile boat like a fishing boat or a Jon boat I recommend using the 40-inch tall guides, part #CE27620. If you have a taller boat like a cabin…

view full answer...

Answer 11

The CE Smith Replacement Hardware for Post-Style Guide-Ons #CE11452-A consists of 3-1/2 x 5-inch long U-bolts and brackets that measure 4-5/8 x 3-7/8 inches, according to my contact at CE Smith. This hardware kit is intended for replacing parts from…

view full answer...

Answer 12

I went out to the warehouse and pulled CE Smith Post-Style Guide-Ons #CE27620 to measure the mounting bracket for you. Overall it is 4-1/8 inches long and 3-7/8 inches wide. The internal width is just a hair over 1-5/8 inches.

view full answer...

Replacement Guide On for CE Smith Guide On # CE27620

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching