Install Instructions for Upgraded Circuit Protected Tail Light Converter Hardwire Kit

Question

Question:

I would like to view the instructions for 119178KIT, But the pdf will not open. I don’t thinks it is me because I can open other item instructions. Can you email me a copy? Thank you.

asked by: JAMES F

0

Expert Reply:

The install instructions for the Upgraded Circuit Protected Tail Light Converter Hardwire Kit part # 119178KIT or part # 119178 are attached to this page for you. The instructions are the same for both models, the former simply comes with a circuit tester and connectors.

expert reply by: Conner L

0

Answer 1

You're welcome! Thanks for all of the information! You could go with the Blue Ox item #BX1139 but I've got a different recommendation that will save you some money and get you a better setup. The Curt RVi battery charger is definitely the way…

view full answer...

Answer 2

Hey Tyler, thanks for the information and welcome back. To add wiring to your school bus you'll need to install the Tekonsha Tail Light Converter with 4-Way Flat Trailer Connector item #119178KIT. This kit includes the powered converter, a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Install Instructions for Upgraded Circuit Protected Tail Light Converter Hardwire Kit

Continue Researching