Center Ball to End of Coupler Dimension of Demco 12564

Question

Question:

Distance from centerline of ball to back end of coupler?

asked by: Mike S

0

Expert Reply:

As shown in the provided photo, the approximate distance from the centerline of the trailer ball to the end of the coupler is 12 inches. The Demco # 12564 accepts a 2 inch trailer ball.

expert reply by: Mike L

0

Center Ball to End of Coupler Distance Demco 12564 2 Inch Trailer Coupler
(click to enlarge)

Answer 1

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 2

I'm assuming you have hydraulic drum brakes and actually need the brake actuator. If that is the case, you're looking at either extending the tongue so you can bolt on an actuator like the #DX33FR or welding one on like the #DEX94FR. Both…

view full answer...

Answer 3

The hole diameters for the Demco Channel Tongue Trailer Coupler item #12564 are 1/2 inch. It is recommended to use grade 8 hardware to attach the coupler to your trailer frame. You can find these bolts at a local hardware store as they do not come…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Center Ball to End of Coupler Dimension of Demco 12564

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching