Grease Seal Recommendation for an Old Boat Trailer

Question

Question:

I removed 2 seals from an old boat trailer 1: marked ATP 13 2: marked ATP 3 I cannot find a cross ref for these? 1.75 ID - 2.35 OD Help! 1960s boat trailer dual axle - 1 with Hyd brakes - 1 free roller Regards

asked by: John J

0

Expert Reply:

It sounds like the Grease Seal # 1105-100-031 that you referenced would be the correct seal for you. This seal has the same inner and outer dimensions your seal has. This seal has a inner dimension of 1.750 and an outer dimension of 2.35.

expert reply by: Jameson C

0

Answer 1

Hey David, so the next smallest sized Bearing Buddy is the part #BB1968 and then #BB1938. That's just a little smaller than the 1.98 size you tried so that is PROBABLY what you need but it would be best to measure first to be sure.

view full answer...

Answer 2

We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…

view full answer...

Answer 3

Since your trailer uses a combined wiring system where the stop and turn signals run on the same circuit, in order to add a third brake light to your trailer you would need to use a 2-Wire to 3-Wire Converter, like part #118158. This will convert the…

view full answer...

Answer 4

The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module #PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light. If there is a specific light style that you are…

view full answer...

Answer 5

Unfortunately we don't have a hub replacement available as you have an odd sized Agricultural Hub. However, I believe I can help you with bearing replacements. You will want #14125A and #LM11949 for your bearings. The for your seal, you will need…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Grease Seal Recommendation for an Old Boat Trailer

Product Page this Question was Asked From

Continue Researching