Rhino Rack Pioneer Platform that Fits Universal Crossbars

Question

Question:

If I want to purchase a pioneer rhino rack platform and Mount it to aero crossbars, can this be done with this platform rack or do I need a different brand ?

asked by: Tiffany L

0

Expert Reply:

Rhino Rack offers versions of their Pioneer Platforms that fit aero bars with the part # RR42114BF for a 48 inch by 38 inch platform or the part # RR42115BF which is 58 by 47 inch.

expert reply by: Jameson C

0

Z R.

3/6/2026

I lost my mounting hardware for my Rhino-Rack Pioneer Platform 44"x 37.5" that allowed my to hook it my default Toyota crossbars. How can I purchase more?

Jameson C.

3/9/2026

@ZR which one do you have specifically?

Zr

3/9/2026

@JamesonC 42115BF is the unit. Rhino just told me they discontinued it and some of the parts no longer exist. I’ll be sure to never purchase any of their products again. That’s crazy that 2 years after purchase you can no longer get a proprietary part for this. Unit is unusable for me without it

Jameson C.

3/9/2026

@Zr That sucks to hear for sure. One of the reasons I like to recommend Yakima and Thule although they cost more is because they have replacement parts for stuff made decades ago. I know that's not helpful now but if you end up needing roof rack components in future that's what I'd go with.

Answer 1

The Rhino Rack Pioneer Platform Rack #RR42114BF inlcudes mounting hardware that will allow you to mount the rack in the T-slots of your vortex aero bars or wraparound the bars with the clamp mount. I've linked our review video of the product that…

view full answer...

Answer 2

You could use pvc pipe and secure it to the frame of the trailer, but that is way overkill and way more work then you need to do to protect the wires. I would just get some wire loom the correct size for however many wires you have to run, and some…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Rhino Rack Pioneer Platform that Fits Universal Crossbars

Continue Researching