Options For RV Slide-Out Tray Assemblies

Question

Question:

I’m looking for 45” extension drawer slides with various load capacity to choose from. We plan to mount them in cargo/basement of 2002 Jayco Designer 5th wheel travel trailer. Thank you

asked by: Lynda B

0

Expert Reply:

We have a couple options close to 45 inches long for slide-out tray assemblies that may work for you. These are rail kits that have a 1,000 lb capacity but do not come with the plywood bottom, that is something you would need to configure. The good part about the Kwikee SuperSlide assemblies is that they do allow you to customize the width, and you can choose from the following lengths, depending on the depth of your cargo department.

- 42" Long: Kwikee SuperSlide I RV Storage Slide Out Tray Assembly # LC370764

- 48" Long: Kwikee SuperSlide I RV Storage Slide Out Tray Assembly # LC370765

The other option is a complete cargo slide assembly from MORryde, and the closest they come to 45 inches long is 36" and 48". These have an 800 lb capacity and also have cargo trays with fixed widths, so the right one would depend on that as well. For example:

- 36" x 29": MORryde Sliding Tray for RV Cargo Compartment # MR27FR

- 48" x 42": MORryde Sliding Tray for RV Cargo Compartment # MR73FR

I have added a link below to a video review for you, as well as a link to our entire selection of RV slide-out tray assemblies.

expert reply by: Kyle S

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 4

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 5

Hey Woody, For your 2025 Grand Design Reflection 337RLS, I don't think you'll have any trouble getting either the MORryde RV Cargo Slide Tray - 72" x 39" - 2 Way Slide - 80 Percent Extension - 500 lbs #MR33FR or the MORryde RV Cargo…

view full answer...

Answer 6

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 7

Hi Chuck! The MORryde RV Cargo Slide Tray - 72" x 26" - 1 Way Slide - 60 Percent Extension - 800 lbs #MR67FR sits 1.6 inches above the floor you mount it on. If you want or need it to be a bit higher off the floor, you can also grab the…

view full answer...

Options For RV Slide-Out Tray Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching