Replacement Ladders & Parts for Motorhome

Question

Question:

My bad! I broke the ladder on my 2020 Allegro Open Road by backing into the mailbox! Is it possible to replace the parts for this? The vertical bar is broken in one point.

asked by: Ted G

0

Expert Reply:

With the verticle bar broken you will likely need a complete ladder to make it safe again. It sounds like you could use a Surco # SP502L Universal Exterior Ladder to replace your broken one. This ladder measures 84-1/2" tall and will work on many motorhomes. If this is not a match for you, check out the links I provided below for other sizes and repair parts.

You might even want to consider a stand-alone collapsible ladder like the TeleSteps # TE64FR 12-1/2' ladder.

expert reply by: Les D

0

Answer 1

Joe, I was able to track down a diagram and find out that the Telesteps Telescopic A-Frame Ladder #TE37FR is 15.4" wide all the way up and down until it reaches the base where it extends to 30.1".

view full answer...

Answer 2

The base of the Telesteps Telescopic A-Frame Ladder #TE37FR has a 49" spread from outside edge to outside edge.

view full answer...

Answer 3

The Telesteps Telescopic Ladder #TE64FR weighs only 24lbs. The small shape makes it much easier to maneuver when carrying it long distances and it is also much easier in windy conditions since you do not have the large framework like a traditional…

view full answer...

Answer 4

Hey Bernard, thanks for reaching out! The Lippert On-The-Go Telescopic Ladder #LC64HD does have the mounting brackets 2 rungs below the top of the ladder, but I do see the case you're making about wanting to lower the brackets even more to make…

view full answer...

Answer 5

I spoke with Lippert about the mounting brackets for the Lippert On-The-Go Telescopic Ladder #LC64HD and found out that they are only sold as an OEM part. This means that only the motorhome/trailer manufacturer is able to order them so you…

view full answer...

Answer 6

Hey Dennis, The bracket the mounts to the trailer wall would need to be installed at the factory and unfortunately isn't an option aftermarket. These are relatively new so I'm assuming after enough people complain to Lippert they'll start…

view full answer...

Answer 7

I recommend using foam tubular pipe insulation on the top rung of your Lippert On-The-Go Angled Telescopic Ladder, #LC64HD if you are concerned with possible damage/scratches to your motorhome. The rung is 1-1/2" so you will want to purchase…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Ladders & Parts for Motorhome

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching