Will the MaxxAir FanMate RV and Trailer Roof Vent Covers Fit a Fantastic Vent Trailer Roof Vent

Question

Question:

Will the Maxxair FanMate fit my fantastic fans. The opening is a standard 14X14.

asked by: Paul G

1

Helpful Expert Reply:

Yes, the MaxxAir FanMate RV and Trailer Roof Vent Covers like part # MA00-955001 will fit Fantastic Vent Trailer Roof Vents. That said, it may require drilling for installation. The trailer roof vents all fit the same 14" x 14" opening.

expert reply by: Conner L

1

Answer 1

All of the RV roof vent covers on the market are designed a bit shorter than need for the vent lid to fully open due to height requirements. That being said, manufacturers have stated that as long as the vent lid opens 50% then the it will still be…

view full answer...

Answer 2

The tallest roof vent cover we offer in white is going to be the MaxxAir FanMate RV and Trailer Roof Vent Cover part #MA00-955001 which is about 10-1/4" at its highest point. I will say that most of the auto-open roof vents will stop raising…

view full answer...

Answer 3

The correct replacement gear motor that replaces the Power Gear 1510000006 on your 2006 Fleetwood Fista is the Replacement PowerGear RV Above Floor Slide-Out Motor #LC368417. The Replacement Gear Motor #LC368193 you were looking at will not work…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will the MaxxAir FanMate RV and Trailer Roof Vent Covers Fit a Fantastic Vent Trailer Roof Vent

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching