Replacement 1200 lb Axle for Starcraft Starflyer Pop-Up Camper

Question

Question:

I had a question in regards to getting a replacement torsion axel for my 1990 Starcraft Starflyer Pop up trailer. what kits would you recommend as suitable replacement.

asked by: William M

0

Expert Reply:

We don't offer replacement torsion beam axles, but we do offer the Timbren Axle-Less suspension that typically doesn't require an axle beam and won't require leaf springs, which could be a good solution for you.

My research indicates that the Starflyer weighed around 1200 lbs. If the ID tag on your pop-up confirms this, we offer some Timbren Axle-Less suspension systems that would work for you.

For the system with 4 on 4 bolt pattern idler hubs included, I'd recommend the # A12RS440. You can see a demonstration video of a typical system by clicking the provided link.

expert reply by: Mike L

0

Maria B.

11/13/2021

Looking to to do maintenance on 92 StarCraft stardust trailer axle 2000lbs. Trying to maintenance hub and axle any advice?

Les D.

11/18/2021

@MariaB I recommend pulling and inspecting the bearings and seals, then repacking the good (or replacement) parts. While you are in there I would recommend inspecting the brake parts for worn or broken parts. Since you have the tires in your hands, inspect them front and back for even the slightest signs or cracking and dry rot, or uneven wear. Tires generally age out before wearing out. If the tires are over 6 years old - replace them. I have attached several articles that you may find useful.

Helpful Links

faq-testing-trailer-brake-magnets-for-proper-function.aspx

faq-trailer-tire-frequently-asked-questions.aspx

faq-wheelbearingpack.aspx

Answer 1

I was able to find info on the part number you listed and you have 10 inch by 2-1/4 inch brake assemblies that are for a 3,500 lb axle. The part #AKEBRK-35R is the correct right hand side assembly for a replacement. For the left hand side you would…

view full answer...

Answer 2

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 3

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 4

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 5

In almost all cases 3,500 lb axles will all use the same bearings. If your trailer has a Lippert or Dexter 3,500 lb axle then yeah they would be the same. But to be safe it won't hurt to pull them off and get the numbers. If you are sure you need…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement 1200 lb Axle for Starcraft Starflyer Pop-Up Camper

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching