Bearing Kit for Horse Trailer with Bearing ID of 1.25 1.75 and Seal 2.25 inch

Question

Question:

I am looking for part numbers for bearings for an older horse trailer. 1.75 inner 3.25 outer 1.25inner 2.32outer seal 2.25 inner 3.36 outer. All of these measurements were done with a micrometer.

asked by: Doug

0

Expert Reply:

Thanks for all of the dimensions you listed! Based on that the correct bearing kit you'd need is the # BK3-200.

expert reply by: Jameson C

0

Answer 1

The correct replacement bearing kit for a 6,000 lb Dexter axle is the following: - Bearing Kit #BK3-100 This comes with the correct replacement bearings, races, and seal for one hub, so you'd need a quantity of two bearing kits for one axle.

view full answer...

Answer 2

Thanks for reaching out, Chris. The best way for you to determine what hubs and bearings you will need is to remove a hub and unpack the bearings. Each bearing should have a number stamped on the edge, or you can measure the OD of each bearing with a…

view full answer...

Answer 3

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Bearing Kit for Horse Trailer with Bearing ID of 1.25 1.75 and Seal 2.25 inch

Product Page this Question was Asked From

Continue Researching