Porch Light Recommendation for Use on Vanagon RV

Question

Question:

is this suitable for porch light on 1986 vanagon? Looking for a warm glow not bright light.

asked by: Charlie M

1

Helpful Expert Reply:

The color of the light that the Low Profile LED Flood Light part # OPT64FR puts out is a bluish white which is very common for LEDs.

For a warmer light that would work great the Omega LED RV Porch Light part # 328-007-30SCPE which puts out a warmer color light and also was intended for porch light use.

expert reply by: Jameson C

1

Answer 1

There really isn't going to be a "typical" size for an oval exterior light, but if your light is overall 4.33" long and has 3.75" between the mounting holes then this light will work for you.

view full answer...

Answer 2

Yes, since the Low Profile LED Flood Light #OPT64FR puts out 1,000 lumens it would easily light up a door/ramp like you mentioned.

view full answer...

Answer 3

It sounds like you're needing a light like the Great White LED Trailer Back Up Light #PE44AR. This has a 7" diameter and a simple 2-wire connection. Since it's a surface mount light you only need to make a small hole for the wiring…

view full answer...

Answer 4

I recommend mounting the Low Profile LED Flood Light #OPT64FR on the upper frame of your trailer. This light is 2" tall and will broadcast the light down at a 45 degree angle. The housings are made of aluminum to help protect the light from…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Porch Light Recommendation for Use on Vanagon RV

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching