Powered A-Frame Jack that Can Fit with 5 inches of Clearance to Propane Tanks

Question

Question:

I need your recommendations for replacing my campers jack. the head cannot be more than 5 inches due to clearance with the propane tanks, it is a 27 foot airstream. thanks

asked by: Glenn G

1

Helpful Expert Reply:

The Lippert Power Stance Electric Trailer Jack part # LC69VR would work really well with the limited clearance you have as you can see in the attached picture that it does not hardly require any clearance behind the jack tube.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hey, Mark! I'm not 100% sure what you mean by wanting to be able to rotate the jack, but you can change how the back is mounted on the trailer so that it's facing another direction. There is a picture attached below demonstrating what I mean.…

view full answer...

Answer 2

No worries Lorelei, I'm here to help! Very nice name by the way; I've never met a Lorelei. You probably can't say the same about my name though haha. Anyways, an electric jack is more of an upright only jack, whereas the manual options…

view full answer...

Answer 3

The Lippert #LC69VR jack is meant for an A-Frame trailer and wouldn't be compatible with a straight or pole tongue trailer like what's used on a boat trailer without extensive fabrication work. This being said, we do have a side-mount powered…

view full answer...

Answer 4

The 3-bolt mounting flange on the Lippert Electric A-Frame Trailer Jack #LC69VR has a standardized hole pattern. The bracket for mounting a jack on a A-frame trailer has a bolt pattern of 3 inches. The bolt holes may be different sizes which is why…

view full answer...

Answer 5

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 6

Yes, I went out to the warehouse and test fit legs on the Lippert Power Stance Electric Trailer Jack #LC69VR and found that the Drop Leg for Lippert Power Jack #LC405217 is a compatible match. This drop leg will slide into the inside of the inner…

view full answer...

Answer 7

Sorry to hear about your troubles and your anger is understandable but we can help you out. It sounds like you have the Electric Ground Control #LC672136, which is for travel trailers. We have gotten questions about a replacement jack for this before…

view full answer...

Answer 8

I spoke with my contact at Lippert and he confirmed that the Lippert Components Power Tongue Jack 1817941 #LC285318 can be rotated to be best orientated for you. The jack can be un-bolted, rotated, and reinstalled.

view full answer...

Answer 9

Hey Kristoper, we have just what you need with the Dometic Furnace part #DMC54RR which has exact same dimensions as what you had at 16 1/2" W X 7" H X 20" D and also this has same 30k BTU rating so it will work perfectly for you. How…

view full answer...

Answer 10

There is only one wire that needs to be connected on the Lippert Electric Trailer Jack part #LC285318. This is the red 12 volt power wire that will need to be ran to the positive terminal on the battery. I cannot be sure as to how the junction box…

view full answer...

Answer 11

The Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs #LC89VR comes with the auxiliary power wire for trailer 7-way power connection. However, the Lippert Power Stance Electric Trailer Jack with Footplate…

view full answer...

Powered A-Frame Jack that Can Fit with 5 inches of Clearance to Propane Tanks

Product Page this Question was Asked From

Continue Researching