How Tight Should Shackle Bolt Nuts Get on Trailer Suspension

Question

Question:

What is the torque value of the bolts with the E99ZR kit?

asked by: Ken

0

Expert Reply:

Shackle bolts don't typically have a specific torque value. They're usually tightened until the knurled portion of the bolt pulls completely into the shackle strap and the bolt head is ran all the way down to the shackle strap and you have at least 2 threads extending past the face of the nut.

This allows the suspension to move like it needs to since it's not tightened down, but the lock nuts keep the bolts from unscrewing.

expert reply by: Jameson C

0

Answer 1

Hello Kevin: yes, a 25-1/4" spring is fine to use in place of a 25-1/2" spring. Generally, we do want replacement springs to be the same size as the originals, but there is a tolerance of 1/2" or less. The 1/4" difference is not…

view full answer...

Answer 2

When looking for replacement equalizers axle spread is a guide and will not give you an exact this fits or doesn't. What you'll need to do is measure center to center of the horizontal holes, and from the center of the top hole to the center…

view full answer...

Answer 3

We have a solution for you but because your axle is already over slung and you have taller hangers in place, we are limited in options. From the images you forwarded, you have a T44 axle. I recommend the Correct Track Trailer Alignment and Lift Kit…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How Tight Should Shackle Bolt Nuts Get on Trailer Suspension

Product Page this Question was Asked From

Continue Researching