10k Trailer Coupler for 2.5 inch wide Tongue for 2 inch Hitch Ball

Question

Question:

I need a 10k coupler for a car hauler with 2inch ball, BUT, the channel size is 2.5. Can you help me out?

asked by: Bill L

0

Expert Reply:

Since you need such a high weight capacity you'd need to use a coupler like the Buyers Products part # 3370091560 which has the capacity you need of 10k, is for a 2 inch hitch ball. You will need to have spacers welded to the sides of the tongue since this is for a 3 inch frame.

expert reply by: Jameson C

0

Answer 1

Because Buyer's Products considers the build sheets and CAD drawings to be proprietary information, they won't provide copies of that. This being said, I pulled one of the #3370091560 Buyers Products couplers from stock and and measured the…

view full answer...

Answer 2

Hey Tony, since the Buyers Products Straight Tongue Trailer Coupler - Auto Latch - 2 Ball - Bolt On #3370091560 that you referenced has a 1/4 inch diameter pin you could use the Master Lock Coupler Lock part #2847DAT to lock the latch.

view full answer...

Answer 3

Yes, most trailer tongues are boxed so you'd simply use one bolt through both sides of the frame to install a coupler like the Buyers Products Straight Tongue Trailer Coupler part #3370091560. In this case you would use three bolts, grade five.…

view full answer...

Answer 4

As the Buyers Products Straight Tongue Trailer Coupler #3370091560 has 3 holes per side on the part that will bolt to the tongue of the trailer, you will want to use 3 bolts per side, so 6 total. This is kind of a standard, so when there are 2 holes…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

10k Trailer Coupler for 2.5 inch wide Tongue for 2 inch Hitch Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching