Replacement Spindle and Hub for my Lippert 3500# Axle

Question

Question:

I am building a trailer spare tire carrier. I plan on mounting a spindle and complete hub assembly on it. That way, I will have a complete hub and bearings available, if needed on the road. My aluminum trailer was made by HandH Trailers using a Lippert 3500# axle. Do you have a spindle and complete hub assembly that would work?

asked by: ROBERT S

0

Expert Reply:

The #84 Spindle for 3,500-lb Trailer Axles part # TRU84FR and the Trailer Idler Hub Assembly for 3,500-lb Axles part # AKIHUB-550-35-K for a 5 on 5" wheel bolt pattern or the Trailer Idler Hub Assembly for 3,500-lb Axles part # AKIHUB-545-35-K for a 5 on 4.5" bolt pattern will have you set up and ready to go.

expert reply by: Randy B

0

Answer 1

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 2

Hi Mark, You’re on the right track with that hub, and we can dial this in so everything matches up correctly. I want to preface my answer by saying we do not carry a spindle and hub assembly in the same kit. The part #AKIHUB-555-35-EZ-K is designed…

view full answer...

Answer 3

Hey Oren, thanks for the information and welcome back! We do not have any replacement hubs with item #LM11949 inner and outer bearings so that would explain your difficulties tracking one down. I saw you were looking at the Trailer Idler Hub Assembly…

view full answer...

Answer 4

Due to the weight capacity of the axle on your M1102 Light Tactical Trailer the only bolt patterns that will fit your spindle are a 6 on 5-1/2" or 8 on 6-1/2". You would have to replace your Spindle #TRU74FR on each side of your axle which…

view full answer...

Answer 5

I have three spindles that are for a 3,500-lb axle and have the bearing dimensions you have listed. The only difference is the dimension for the grease seal is 1.75 inches, not the 1.795 inches that you have mentioned. Maybe you typed in the seal…

view full answer...

Answer 6

The Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKEBRK-35 has a mounting pattern that is typical for 3,500 lb axles. The center on center horizontal measurement of the mounting bolts are 2-7/8 inches and…

view full answer...

Answer 7

Hello John, I sure can! The #84 E-Z Lube Spindle #TRU74FR uses the #L68149 (1.378" inner diameter) inner bearing and L44649 (1.063" inner diameter) outer bearing. I have included detailed measurements for this spindle below.

view full answer...

Answer 8

In order to determine if hub assembly 8-258-50UC1-EZ will work for you, first know that this assembly is for EZ Lube spindles that require a grease seal with a 1-1/2" inner diameter such as #RG06-020. You are also going to want to remove the hub…

view full answer...

Answer 9

I wasn't able to find anything in regard to a replacement part for your TDE 11029C hub assembly, but if you can pull your hub and either look for bearing/grease seal parts numbers or measure the different locations on your spindle then I can see…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

When installing a hub like the #AKIHUB-545-35-K on the #TRU84FR the hub is going to stop where the grease seal sits. If you look at the attached picture below, you will see the measurement marked F which is 6-1/2". This would be the stub length,…

view full answer...

Answer 12

The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Say…

view full answer...

Replacement Spindle and Hub for my Lippert 3500# Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching