Brake Controller Connector Location on 2019 Cadillac Escalade

Question

Question:

I can’t find where the wire harness plugs into on my 2019 Escalade...trying to install one of your electric brake controllers I have looked everywhere under dash...by foot pedals as well under the hood

asked by: Sandy

0

Expert Reply:

On a 2019 Escalade, the plug you're looking for is in a junction box on the firewall to the left of the brake pedal. The junction box has a black cover, which will need to be removed and the # 3016 harness you'd looked at will plug into the socket shown in the provided photo. The top photo shows the location of the junction box, the bottom photo shows what the Junction box looks like with the cover removed and the exact location where the harness plugs in.

The # 3016 is the harness you'd need for a Draw-Tite or Tekonsha Brake Controller like the P3, part # 90195. The P3 is one of my favorites due to it's user friendly display and controls.

expert reply by: Mike L

0

click to enlarge

Answer 1

For your 28' enclosed trailer I recommend the Furrion Chill HE RV Air Conditioner System - Single Zone - 15,000 Btu - Black #FR23PV. If the ceiling of the trailer isn't too high and you can reach the air distribution box and don't want to…

view full answer...

Answer 2

The brake controller connection is in the same spot as found in the Suburban or the GM full sized trucks of that generation. It's located in a junction box behind and to the right of the emergency brake pedal. You'll need to remove the cover,…

view full answer...

Answer 3

I recommend Indoor RV Speaker - Recessed Mount - 6-1/2" Diameter - 35 Watts - White - Qty 1 Item #324-000001. The inner diameter is 5" so it will fit inside the 5-3/4" hole you currently have. The mounting plate is going to be just…

view full answer...

Answer 4

What you described is perfectly normal. When not connected to a trailer the Prodigy P2 part #90885 will show two dots like you described. After a period of inactivity the controller will go into sleep mode. It doesn't turn off with the vehicle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Brake Controller Connector Location on 2019 Cadillac Escalade

Continue Researching