26 inch Leaf Spring Replacement for Trailer with 2,000 lb Axle

Question

Question:

I would estimate 2000 pounds. Is there a complete kit with the 26” springs? What is part number?

asked by: Tom

0

Expert Reply:

You'd need the longer size you mentioned, do you know what capacity axle you have?

expert reply by: Jameson C

0

Tom

11/4/2020

I would estimate 2000 pounds. Is there a complete kit with the 26” springs? What is part number?

Jameson C.

11/4/2020

We have a 26 inch long 2,000 lb axle leaf spring with part # e77SR.

Answer 1

When using the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles part #e27SR with the Single-Axle Trailer Hanger Kit for Double-Eye Springs part #APS4 you will need to space the leaf spring hangers 25-3/4" apart.

view full answer...

Answer 2

Hello Zane, thanks for reaching out. Unfortunately, we do not carry any leaf springs that are this long. The longest spring we have is 30-1/2" long, and these are rated for much larger axles than yours. For a small single axle trailer, most of…

view full answer...

Answer 3

It makes no difference which direction the shackle nut or bolt head is facing. The bolt is not driven in, when the shackle bolts are tightened, the knurled portion of the bolt will be drawn into place. Make sure you use a lock nut, and snug it down…

view full answer...

Answer 4

There should be 2 inches minimum between the tires on a dual axle trailer. This will allow the suspension components room to work properly but a little more room is ideal. For instance the Ultra-Fab Chock and Lock Wheel Stabilizers for Tandem-Axle…

view full answer...

Answer 5

The closest thing we have in those dimensions is the Single Axle Trailer Fender for Boat Trailers item #HP48VR. It measures 9" Wide x 32" long x 14" tall. You can weld the fender onto your trailer or use the Mounting Brackets for…

view full answer...

Answer 6

The U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles part #APUBR-10 is what I recommend for the Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs part #e37YR.

view full answer...

Answer 7

The 2x2 inch square axle is likely 3,500 lbs or less capacity. I would need more spindle dimensions or bearing numbers to assist. If you pull a hub and measure at the spindle where the bearings and seal ride using the digital caliper like #PTW80157 I…

view full answer...

Answer 8

The Fulton Plastic Fender, part #F008582, does not include mounting hardware. The Fulton fender is designed to be mounted with your existing hardware, or with brackets designed that are specific to the trailer frame on which they are to be installed.…

view full answer...

Answer 9

Hey Terry! In order to mount the CE Smith Fenders #CE19504-2, normally I recommend #CE26098G-2 or #CES54XR (x 2) depending on your application. Do you know if you need the 90 degree bend to attach to the frame of the trailer, or the straight bracket?…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

Hi Steve! For salt water applications, I always recommend Aluminum wheels. Galvanized steel will hold up better than raw or painted steel, but aluminum is king in this regard. You still want to clean them off after they get all salty as aluminum does…

view full answer...

Answer 12

The slipper spring hook of a slipper spring like part #e67SR attaches to the equalizer and the eye of the spring attaches to the hangers of Tandem-Axle trailer hanger kit part #APT6SE. I have attached a diagram of how slipper springs are setup. I…

view full answer...

26 inch Leaf Spring Replacement for Trailer with 2,000 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching