Replacement Mounting Brackets for MaxxTow Roof Cargo Basket

Question

Question:

Are replacement brackets available for this product?

asked by: Robert P

0

Expert Reply:

There are not direct replacement mounting brackets available for the MaxxTow Roof Cargo Basket MT70115, but you might be able to make the Rola Replacement Roof Mount Bracket Assembly # 59506 work on this cargo basket. I've linked a photo with some dimensions that you can use as a comparison and decide if they'll work for your application or not.

expert reply by: Erik B

0

click to enlarge

Answer 1

We have the replacement mounting hardware for the Yakima Megawarrior with the lock setup with part #Y07064 and we have quite a few in stock.

view full answer...

Answer 2

Hey Sven! I'm sorry to hear that, is your vehicle ok? At least they didn't manage to remove and steal your roof basket. To replace the straps on your Yakima OffGrid #Y07138 you need the replacement brackets. You can choose from the following…

view full answer...

Answer 3

It looks like the Rola hardware of the roof basket #59504 will be able to be replaced with the locking hardware from Yakima #Y07064. Due to the slight differences in the mounting hardware, you will need to replace all 4 mounts. I've attached the…

view full answer...

Answer 4

The mounting bracket for the TorkLift GlowStep Stow N' Go Scissor Steps #TLA7834 is 23" wide x 3-1/2" tall if you measure from outside edge to outside edge. With the retention straps/rest of the bracket on the sides included you're…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 12

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps! For…

view full answer...

Replacement Mounting Brackets for MaxxTow Roof Cargo Basket

Continue Researching