Backing Plates for Trailer Fenders

Question

Question:

Do you have a back panel for that fender the solid piece that goes across the back side

asked by: Jim C

0

Expert Reply:

We do offer backing plates for trailer fenders, depending on whether you have a single axle or double axle trailer.

- Backing Plate for Tandem-Axle Trailer Fender - 69" Long x 12" Tall # HP72FR

- Backing Plate for Single Axle Trailer Fender - 30" Long x 10-1/2" Tall # HP62FR

I have added a link below to a video review for you to check out as well.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 4

I was able to find the exact replacement amber (1A-S-20A) and red (1A-S-20R) lenses. I did a Google search on kaper2 (or Kaper II), and found replacement lenses. Their replacement lenses are shown as measuring 4 inches long, by 2 inches wide by 3/4…

view full answer...

Answer 5

Hey Dan. We've got three options that are close to your dimensions for a Jeep style fender. I have listed them below: Diamon Plate Single Axle Trailer Fender 13" to 15" Wheels item #CE18041ATB - 36" long x 10" wide x…

view full answer...

Answer 6

Hey Nick, thanks for the information! For 205/75d15 tires you'll need a fender designed for 15" wheels that's at least 27-1/2" wide if the fender is going to sit near the widest part of the diameter of your tires. The Single Axle…

view full answer...

Answer 7

If the towing capacity of your 2016 Jeep Cherokee Sport with the 2.4 I4 engine is 2,000 lbs then the gross weight of the trailer cannot exceed 2,000 lbs. I am not totally sure what you are looking for as a size clarification but for trailer's…

view full answer...

Answer 8

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 9

Hey Paul, are you asking about replacement zerk fittings that would fit the spindles of the axle? If so, this is not an EZ lube axle so it doesn't have those or have ability to have them added. Or were you asking about Bearing Buddies that…

view full answer...

Answer 10

Hello Al, Happy to get those for you. I would want to take a gander at them too, just to see what I’m getting myself into. I was able to get the instructions for the Advent Air Low Profile RV Air Conditioner System, Single Zone, 15,000 Btu, White,…

view full answer...

Backing Plates for Trailer Fenders

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching