What is 22 mm Size of Wheelmaster Lug Nut # WM9062 Refer To

Question

Question:

Does the 22 mm dimension of the WM9062 refer to the thread size ID, or the measurements across the flats of the hex? If the thread size, what is the dimension across flats of the hex?

asked by: Scott B

0

Expert Reply:

The 22 mm size that is mentioned for the Wheelmaster lug nut part # WM9062 that you referenced is the size of the thread.

expert reply by: Jameson C

0

Answer 1

Hi Dan, It sounds like you need a jam nut extender or an integrated jam nut cover. Unfortunately, we don't carry either of these and only offer commercial nut covers and jam nuts themselves. A more specialized trailer parts store may offer them…

view full answer...

Answer 2

We do have the 22 mm version of the Replacement 20 mm Lug Nut for Wheel Master Wheel Liner #WMRMT9063. The #WM9062 is what you're looking for. Also yes, the Replacement Wheel Master Lug Nut Cover #WMRMT9061 will fit the 22 mm so you won't…

view full answer...

Answer 3

The lug nut cover part #WMRMT9061 is made from stainless steel and could work if you have a 20 mm lug nut on your wheels like the part #WMRMT9063 that this was designed to fit. We do not have anything made from tin though.

view full answer...

Answer 4

I measured the Replacement Wheel Master Lug Nut Cover #WMRMT9061 and it has an overall height of 1.6 inches.

view full answer...

Answer 5

The Replacement 22 mm Lug Nut for Wheel Master Wheel Liner #WM9062 is a 22mm nut, so you'll need a metric socket set with a 22mm socket. You might be able to make a 7/8" socket work, but you'd really be risking stripping the nut with the…

view full answer...

Answer 6

Can you send those pictures as a reply to this e-mail?

view full answer...

Answer 7

I found your Dicor V160FOLNC lug nut cover, and while we do not have a direct replacement we do have something that is pretty close that should work. Check out the Replacement Wheel Master Lug Nut Cover for Wheel Liner #WMRMT9061. This lug nut cover…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

What is 22 mm Size of Wheelmaster Lug Nut # WM9062 Refer To

Product Page this Question was Asked From

Continue Researching