Lift Kit for Trailer With Stealth Trailer that Has Tandem 3,500 lb Lippert Axles

Question

Question:

I have a 8.5x20 stealth trailer and I Believe they have a lipper tendem Suspension and I need to lift it a few inches 4-5 inches if possible, or what’s the highest lift for lipper tendem axles that you have? can you please help me with the kit or parts # so I can purchase it Please thanks

asked by: Isaac D

0

Expert Reply:

Does you trailer have leaf springs or torsion springs if you look underneath it? Any idea what the axle capacity is?

expert reply by: Jameson C

0

Isaac D.

8/28/2020

I have a 8.5x20 stealth trailer and I Believe they have a lipper tendem Suspension and I need to lift it a few inches 4-5 inches if possible, or what’s the highest lift for lipper tendem axles that you have? can you please help me with the kit or parts # so I can purchase it Please thanks

Jameson C.

8/28/2020

Thanks for getting me that info! Based on that the correct lift kit you need is the Lippert Tandem Axle lift kit part # LC407131 that you referenced. This will give you a 2 inch lift for both axle.

Answer 1

To lift your Little Guy 5 trailer, you will want to use the Dexter Axle Torflex Lift Kit - Single Axle #K71-707-01. This will lift your axle to give you an additional 2-5/8 inches of ground clearance on your trailer.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The lift kits we carry fit with specific axles; the #K71-725-02 is a tandem axle application and will give a 3-1/8" lift and is compatible with side-mounted #12 Torflex axles with 5,500-7,000-lb capacities. If that is what your axle is, this kit…

view full answer...

Lift Kit for Trailer With Stealth Trailer that Has Tandem 3,500 lb Lippert Axles

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching