Universal Stoplight Switch Solution for Brake Controller Install in 2020 Jeep Cherokee

Question

Question:

how do I get a brake pedal signal on a 2020 Jeep Grand Cherokee without factory tow package Appears like wire 4 going to brake pedal position sensor are small gauge wires, maybe just signal wires to a control module ?

asked by: Russ W

0

Expert Reply:

We have an easy solution to provide a stoplight circuit on your 2020 Jeep Cherokee with the Roadmaster Universal Stop Light Switch Kit # RM-751000. Some vehicles have a hard time finding the stoplight circuit but this switch solves the problem.

expert reply by: Jameson C

0

Answer 1

We do have a solution for you, though the Reese Trailer Connector Adapter #78118 will not work for you. Instead I recommend the Hopkins Endurance Quick-Install Trailer Connector Adapter #HM47200 which will plug into your truck's 4-way and allow…

view full answer...

Answer 2

Before installing the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires #ETBC7 you will need to have a 4-pole wiring harness already installed. If you do not then I recommend the Curt Vehicle Wiring…

view full answer...

Answer 3

Yes, the cold side of the brake light switch would be where you would need to splice into for the braking signal. While we don't have wiring schematics for your motorhome I do still have two options for getting the signal. Option 1: You can use a…

view full answer...

Answer 4

For your 2022 Ford E-450 cutaway chassis the correct Tekonsha brake controller install harness is actually the part #22292. This is why what you have doesn't look like it would work with the 3035-P.

view full answer...

Answer 5

The difference between the #RM-4700 and the #RM-4750 is being able to use them with your base plates. If you have the crossbar on your base plates you will need part #RM-4700. The RM-4750 is not compatible with other style base plates. Since you said…

view full answer...

Answer 6

The least expensive way to activate the charge circuit of your 2020 Jeep Cherokee Trailhawk's 7-way will be to run a length of 10 gauge wire like part #10-1-1 (sold by foot) from the positive post of the vehicle battery to the 1:00 pin of the…

view full answer...

Answer 7

When installing your Tekonsha Prodigy P3 Controller you will need the Tekonsha Custom Wiring Adapter #3014-P. This dual plug in adapter will plug into the brake controller and the other end will plug into the built in port beneath your vehicle's…

view full answer...

Answer 8

I can help you install a brake controller like the Tekonsha P3 on your 2015 Jeep Cherokee. For Brake Controller recommendations, I really like the #90195. This brake controller is a proportional controller, which means whatever pressure you press the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Universal Stoplight Switch Solution for Brake Controller Install in 2020 Jeep Cherokee

Products Featured in This Question

Continue Researching