Hanger Spacing When Using Leaf Springs SP-212275 with Hanger Kit APS4

Question

Question:

When using APS4 Hanger kit for the referenced springs, what is the correct spacing?

asked by: Tom

0

Expert Reply:

When using the hanger kit part # APS4 with the leaf spring part # e54SR the distance between the hangers will be 24-7/8 inches.

expert reply by: Jameson C

0

Answer 1

It is possible to install double eye leaf springs on your trailer, yes but you will need to cut off your old hangers and install new ones. However, if the leaf springs that you had on your trailer were old and worn then there is a chance they could…

view full answer...

Answer 2

The Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 will work well for your 1-3/4 inch wide leaf springs. Double eye springs are the style have both the bolt in the front and rear and are more common…

view full answer...

Answer 3

For your single axle boat trailer, I recommend the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 along with the 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 23-1/2" Long #SP-113275.…

view full answer...

Answer 4

Instead of changing the geometery of the original design which could cause issues the 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles part #e84SR has the exact same specifications as the one you have however it has a 20-3/8" center to center…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Hanger Spacing When Using Leaf Springs SP-212275 with Hanger Kit APS4

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching