Replacement Hub and Drum With 25580 Inner Bearing and LM67048 Outer Bearing
Published 08/23/2020 >
Products Featured in This Question
Question:
hello, I need to repace old hubs with new hubs and tire rims . The Bearings are LM67048/25580. The Brake assembly on the axle is no lon ger in use and will not be needed. What would you suggest without breakin the budget? I want to get away from the old rims shown in one of the pictures
asked by: Daniel S
Expert Reply:
Thanks for that info and we do have a replacement hub and drum for you with inner bearing # 25580 and outer bearing # LM67048, though you are going to need to take one more measurement, and with Digital Caliper # 301-17068 because it needs to be measured down to the thousandth of an inch.
So, the correct hub and drum will depend on the size of the grease seal, and you'll need to measure your spindle where the seal rides to get that measurement.
- 2.25" Diameter: Dexter Trailer Hub and Drum Assembly # K08-201-97
- 2.15" Diameter: Dexter Trailer Hub and Drum Assembly # 8-201-5UC3
These are rated for 5,200 lb axles and have a 6 on 5-1/2" bolt pattern so that is the bolt pattern of the wheels you will need. I have added a link to our selection of trailer tire and wheel combos with that bolt pattern for you to check out as well.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly - 5,200-lb Axles - 12" - 6 on 5-1/2
- Trailer Hubs and Drums
- Hub with Drum
- 25580 / LM67048
- Standard Grade
- For 5200 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Search Results: electric jack
- Search Results: hold back
- Video: Setting up the etrailer Trailer Hitch Receiver on a 2017 Chrysler Pacifica
- Search Results: battery tray
- Search Results: gh~614
- Search Results: progrip
- Search Results: ramp door spring
- Search Results: bw1123
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb Axles - 12" Diameter - 6 on 5-1/2
- Q&A: Replacement Hub w/a 6 on 5-1/2 Bolt Pattern for a M1101/2 Trailer
- Shop: Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 10" Drop/Rise - 16K
- Shop: Lionshead Trailer Wheel Lug Nut - 1/2"-20 - Stainless Steel - Qty 1
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 3-1/2" Wide - Surface Mount - 1,600 lbs
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 3-9/16" Wide - Recessed Mount - 400 lbs
- Shop: Americana Modular Wheel w/ +0.5 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Black
- Video: Equalizer for 1-3/4" Wide Double-Eye Springs Review
- Q&A: Replacement Idler Hub Options For A Dexter 8-135 Idler Hub
- Shop: Brake Controller
- Video: Hands-On with the Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles
- Video: A Closer Look at the Dexter Trailer Hub and Drum Assembly
- Q&A: Direction of Equalizer # TREQ105 When Installed on Triple Axle Trailer
- Q&A: Replacing Mobile Home Trailer Hub With a Hub that is Compatible with Standard Rims and Tires
- Shop: Gooseneck Hitch
- Video: Installing the B&W Turnoverball Underbed Gooseneck Trailer Hitch in a 2025 Chevrolet Silverado 1500
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Wiring
- Video: The Low-Down on the Trailer Hub and Drum Assembly
- Shop: Trailer Wiring








Daniel S.
8/23/2020
hello, I need to repace old hubs with new hubs and tire rims . The Bearings are LM67048/25580. The Brake assembly on the axle is no lon ger in use and will not be needed. What would you suggest without breakin the budget? I want to get away from the old rims shown in one of the pictures