Pop & Lock Power Lock Conversion Kit for Leer 100XL, Leer 100XQ, and Leer 700 Camper Shell

Question

Question:

I would like to add a pop lock system to my shell. I need to know which one to get to fit this locking mech? Leer 100XL, Leer 100XQ and Leer 700

asked by: Chris B

0

Expert Reply:

I checked with Pop & Lock for you and there is a system that they have confirmed will work with 2011 and newer Leer 100XL, Leer 100XQ, and Leer 700:

- Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers # PAL9772

expert reply by: Kyle S

0

Answer 1

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.

view full answer...

Answer 2

The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade your existing…

view full answer...

Answer 3

The conversion kit you are talking about would be the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772. I checked with Pop and Lock though, and according to them the #PAL9772 is for 2011 and up model year Leer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Pop & Lock Power Lock Conversion Kit for Leer 100XL, Leer 100XQ, and Leer 700 Camper Shell

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching