Which 1-1/4 inch to 2 inch Hitch Adapter Can Fit Class I Hitches

Question

Question:

I wanted to use an existing bike rack that has a 2 inches opening. I noticed this adapter mentioned its for Class II hitch but I wanted to know if it will fit Class I hitch from Curt #C11473? Thank you,

asked by: Ken N

0

Expert Reply:

We have a 1-1/4 inch to 2 inch hitch adapter that is compatible with Class I 1-1/4 inch hitches like the part # HTAD or for a similar setup that provides additional rise you'd want the part # HT5R.

expert reply by: Jameson C

0

Answer 1

The Curt Trailer Hitch Receiver - Custom Fit - Class I #C11681 is a confirmed fit for your 2017 Honda Accord Sedan and at this time there is not a Class II hitch available. If you will be towing with this hitch, I recommend the ball mount #C45521 and…

view full answer...

Answer 2

Hey Dylan, so we have the Brophy hitch expander part #HTAD which is Class I compatible but the adapter you mentioned can only be used with Class II hitches so it wouldn't work for you.

view full answer...

Answer 3

I have a solution for you, but the distance from the hitch pin hole of the Curt adapter part #C45785 to the back of the hitch opening is 2.55 inches so it would not be deep enough for your bike rack. Instead we have the Brophy hitch adapter part…

view full answer...

Answer 4

I can help you find out what's going on with your heat shield on your 2012 Honda Accord. According to Curt's directions, the heat shield only needs slight trimming and should be reinstalled after installation of the trailer hitch. I've…

view full answer...

Answer 5

From the center of the pin hole of the part #HT5R to the back of the upper hitch opening tube measures 3-1/2 inches. You would need to have less than 3-1/2 inches from the pin hole on your hitch out to the furthest point out on the rear bumper. When…

view full answer...

Answer 6

Yes, if you installed the Curt hitch part #C11681 on your 2013 Honda Accord with dual exhaust you would need to trim the heat shield on both sides.

view full answer...

Answer 7

I do have a solution for you but using a hitch adapter like #HT5R, reduces your hitch capacity by 50 percent, so it's not ideal. The best option I can offer is the Curt Cargo Carrier #C18110, which has a shank with a built in rise of 3-3/4…

view full answer...

Answer 8

I have a different option for you, but I do not recommend using the Hitch Adapter #HT5R with the Curt Trailer Hitch Receiver #C11681 for your 2016 Honda Accord Sport Coupe as it will reduce the tongue weight rating of the hitch by 50% which will give…

view full answer...

Answer 9

Hey Chris, thanks for reaching out! I checked with out manufacturers and unfortunately it looks like the only hitch receiver sizes designed to fit your 2024 Honda Accord are the smaller 1-1/4" receivers. You can technically use a hitch adapter…

view full answer...

Answer 10

On adapter #HT5R it measures 3-1/2 inches from the center of the hitch pin hole to the back of the upright that supports the 2 inch receiver. For Curt hitch #C11681 for the 2013 Honda Accord it should measure about 2-1/2 inches to clear the rear…

view full answer...

Answer 11

The hitch receivers available for your 2015 Honda Accord are all Class I with a 1-1/4 inch receiver opening like the Custom Fit Curt Hitch, #C11681. Curt does require the use of Support Straps, #18050, for all non-trailer loads including bike racks,…

view full answer...

Answer 12

Currently the only receiver options for your 2021 Honda Accord Touring 2.0T sedan are class I, 1-1/4" receivers like the Curt #C11525. The EcoHitch Receiver #306-X7299 you found will only fit older Crosstour models. While we do have an Adapter…

view full answer...

Which 1-1/4 inch to 2 inch Hitch Adapter Can Fit Class I Hitches

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching