Replacement Motor For Lippert Ground Control Leveling System On 2018 Keystone Laredo Travel Trailer

Question

Question:

I need a replacement motor for a lippert 3.0 front rh jack part # 388897.

asked by: Mark P

0

Expert Reply:

The Replacement Stabilizer Motor and Gearbox for Lippert Components Ground Control TT Leveling System # LC656216 or the Replacement C-Jack for Lippert Components Electric Ground Control TT # LC404488 are the replacement parts available for your Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs # LC672136. Just the motor is not available as a replacement part for that system.

expert reply by: Jason S

0

Answer 1

We have the part number you are looking for with #LC404488 which gives you the replacement leg and motor you are looking for. Based on what you described experiencing this is the correct solution for your problem as well.

view full answer...

Answer 2

The Furrion Vision Wireless RV Backup Camera System FOS48TA-BL is the older generation and will not work with the Furrion Vision S Wireless RV Backup Camera part #FCN48TASF which is the new generation. The only other option would be to upgrade to the…

view full answer...

Answer 3

I attached a link on this page to the owners manual/install instructions for the Demco Hijacker Autoslide 13k hitch part #DM8550040 that you referenced for you to check out.

view full answer...

Answer 4

The Fastway e2 weight distribution (WD) 8,000 lb and 10,000 lb systems do use the same head units so you can easily use the 1,000 lb Trunnion Bars #FA92-01-1099 or 2 of the Rounds Bar #FA94-02-1099 with your current setup depending on which you have.…

view full answer...

Answer 5

I reached out to my contact at Lippert and he said there are a couple of things you will want to look at to try and troubleshoot the blank display on your Level Up touch pad. He said to first remove the pad itself from where it's mounted (keeping…

view full answer...

Answer 6

A couple of things to check when trying to pair monitor to the camera for the Furrion Vision S #FOS43TASF. First make sure that the monitor is close enough to the camera. Next make sure that the camera is receiving power (indicated by LED light on…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...