Bearing Buddies that Measure 2-1/8 Inches in Outer Diameter

Question

Question:

Outside diameter is 2 1/8. Tried 1 9/8, way too Small. Tried 2.4inch way too Big. HELP. Just bought this 2nd hand trailer and have NO info on this.

asked by: Richard

0

Expert Reply:

When selecting bearing protectors the measurement needs to be as accurate as possible so you will need to use dial calipers. We have a digital set we use here for precise measurements. Since 2.24 is too large and 1.98 is too small the size in the middle is 2.08 like # BB2080. For replacement bras you would use # BB19B.

expert reply by: Michael H

0

Answer 1

Since the outer diameter of your Bearing Buddy Protectors is 2-1/8", you'll want the Replacement Bearing Buddy Bras - Model 19B - (Pair) item #BB19B. These are sold as a pair so you'll need one set per axle. What kind of boat do you…

view full answer...

Answer 2

If the outer diameter of your Bearing Buddy measures 2.125" then you need the Model 19B Replacement Bearing Buddy Bras #BB19B. These are compatible with models that have an outer diameter of 2-1/8" (or 2.125" in decimal form). Attached…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Bearing Buddies that Measure 2-1/8 Inches in Outer Diameter

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching