How To Wire Up Hopkins Engager Push-To-Test Trailer Breakaway Kit

Question

Question:

If you put power to both sides of the break away switch like in the installation video won’t the brakes be engaged all the time? The wiring directions in the video seem way wrong.

asked by: Casey

0

Expert Reply:

In regards to the Hopkins Engager Push-To-Test Trailer Breakaway Kit part # 20400, there are only two wires with the black being power so it should be run to the positive battery terminal and the blue being brake output so it should be run to the brake output circuit.

I have attached a wiring diagram you should use below.

expert reply by: Conner L

0

click to enlarge

Answer 1

The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part #APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that would be…

view full answer...

Answer 2

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 3

Hey Calen, Appreciate the business and we do have the right wheel studs for your Dexter 9-123 hub. They are drive in/press in studs as well, and 5/8" like you mentioned. The correct part for you is the following: - Replacement Dexter Axle…

view full answer...

Answer 4

We do have the stainless steel replacement caliper bracket you are wanting with part #KCMB12S, or for Dacromet we have part #KCMB12D. Stainless steel is the best in terms of corrosion resistance but Dacromet does a great job as well. If you will be…

view full answer...

Answer 5

I have attached the installation instructions for the Hopkins Engager Trailer BreakAway Kit, part #20099. This kit includes a charger and an LED tester and will work with single and tandem axle trailers. I have also attached a link to an installation…

view full answer...

Answer 6

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

I contacted the manufacturer regarding the installation of the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR. They were able to provide me with a wiring diagram which I have included here for you.

view full answer...

Answer 9

Yes, there is a measurement you can take to determine what size brakes you need and if they will fit your existing drums. You will want to measure the diameter of your drums. I have included a diagram detailing the dimensions you will need to find.…

view full answer...

Answer 10

The black wire from the break away switch will connect to the blue wire from the break away box, as shown in the provided diagram. By 'brake wires' I'm assuming you're speaking of the wires connected to the brake magnets on your brake…

view full answer...

Answer 11

The 7 Way Trailer Connector Vehicle Tester part #C73NR should work well to test the trailer battery charge line on Ford trucks with the Smart Tow Package because as you mentioned the trailer battery charge line is not active until a trailer is…

view full answer...

Answer 12

Without knowing what brake controller you have I will venture to guess that the OL code you are seeing is an over load code. The OL or overload error code indicates a short in the brake output circuit. Start by examining the trailer connector. Make…

view full answer...

How To Wire Up Hopkins Engager Push-To-Test Trailer Breakaway Kit

Continue Researching