Suspension Enhancement Recommendation for 2003 Toyota Tundra with B and W Turnoverball

Question

Question:

2003 Toyota Tundra SR5 4wd 4.7 engine Will these work with a B and W turnover ball hitch?

asked by: John N

1

Helpful Expert Reply:

I have a really great suspension enhancement kit that fits your 2003 Toyota Tundra with the B and W Turnoverball hitch # BWGNRK1251 you have but none of the air bag style kits we offer will fit with an in-bed hitch. Instead the best option by far is the RoadActive Suspension kit part # RAS34FR which gives you the support you are wanting when towing but also improves ride quality when you aren't towing as well so it's by far the best option.

expert reply by: Jameson C

1

Answer 1

Yes, the Timbren Rear Suspension Enhancement System part #TFR1502D for 2WD or part #TFR1504D for 4WD will work with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1104 you have installed in your 2012 Ford F-150. The mounting…

view full answer...

Answer 2

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 3

To add a 7-Way trailer connector at the rear of your 2002 Toyota Tundra you will need to install a 4 and 7 Way Installation Kit, #ETBC7. This will require route and splicing some wires. What you will do is plug your existing 4-Way into the back of…

view full answer...

Answer 4

I have a way for you to install either a P2 Brake Controller part #90885 or a P3 #90195 in your 2002 Toyota Tundra but there isn't a plug-in adapter available that would work. You will need to hardwire the controller in. Since you do not have a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...