Will Grease Seal 13194 Fit with Dexter Axle 8-258 Hub

Question

Question:

Does the dexter #13194 inner grease seal fit with the 8-258 dexter hub and a 1 1/16inch btr spindle which has a 1 3/8inch approx flange that the grease seal rotates on. Im having a hard time finding this particular grease seal for an older coleman taos pop up camper. It seems the new grease seals have either a 1 1/4inch or 1 1/2 inner diameter for newer spindles.

asked by: Ronnie

0

Expert Reply:

Yes, the Grease Seal # 13194 will fit just fine with a Dexter Axle 8-258 like part # 8-258-5UC1.

I would verify fitment of this seal with your spindle by using a digital caliper like part # 301-17068. What you'll want to do is measure the diameter of your spindle where the grease seal rides. The seal # 13194 mentioned above has a 1.372" ID.

expert reply by: Jon G

0

Answer 1

Pulling the wheels and hubs off of your 5th wheel trailer is the best option when trying to identify what wheel bearings and seals are installed. On the back of the wheel bearings there usually is printed a part number like #L44643. With these…

view full answer...

Answer 2

I went out to the warehouse and found that the TruRyde Grease Seals #RG06-020 that you referenced are 1/4" thick. If the ID and OD are correct for your application then this is the correct set of grease seals for you as those are the determining…

view full answer...

Answer 3

The Atwood #AT3308046006 cover that you selected will likely work just fine. I contacted the manufacturer and they did not have your model 600315.321 so I can't spec out the exact one. There may be another sticker on your unit ending in .331 or…

view full answer...

Answer 4

For a Dexter hub 8-258 the correct seal is the part #10-9.

view full answer...

Answer 5

For the Dexter hub 8-258 you have the correct replacement seal is the part #10-9 which has a 1.5 inch inner diameter.

view full answer...

Answer 6

Hey Duane, Once the bearings are packed with grease and the hub is on the spindle you'll need to slowly pump grease into the spindle until you see it start to seep out of the outer bearing. Be sure to use a manual grease gun so the grease…

view full answer...

Answer 7

Trailer tires should be inflated to the maximum psi indicated on the tire. If your tires read 50 psi then that is what you will want to inflate them to. The trailer tires cannot reach their capacity rating unless inflated to the maximum. Trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Grease Seal 13194 Fit with Dexter Axle 8-258 Hub

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching