Replacement Control Unit for Kwikee Steps Part 094707-04-700

Question

Question:

Step control unit. 2008 Itasca sunrise #094707-04-700

asked by: Brian H

0

Expert Reply:

I was able to look up part number 094707-04-700 and find the correct replacement control unit for the Kwikee steps in your motorhome.

The correct part is the Replacement Control Unit for Kwikee Electric RV Steps # LC379146.

expert reply by: Kyle S

0

Answer 1

If you are currently using 909510001 then you will need #LC379605. The other one, #LC379146, is for pre-IMGL steps. IMGL stands for integrated motor/gear box/linkage. In October of 2004, Kwikee began shipping steps with an integrated motor/gear…

view full answer...

Answer 2

The Kwikee Control Box #909506000 has been discontinued by the manufacturer. The replacement part is determined by the date of manufacture which you can determine by looking at the current part which will have a date on it. If not, you can supply the…

view full answer...

Answer 3

The Replacement Control Module for Lippert Electric Coach Step #LC301702 is the correct fit for your Lippert Coach step. The long green wire with the ring terminal is your ground and will be attached bare metal to metal on our coach frame. The short…

view full answer...

Answer 4

It sounds like you have a couple wires run backwards on your Lippert powered steps. Its hard to say exactly which wires are wrong but most likely a power wire and ground is backwards. The best recommendation I can give would be for you to go over the…

view full answer...

Answer 5

To find the fuse for your Kwikee Electric RV Step Complete Assembly #LC3658373 you'll need to trace the power wire from the switch to the battery. If you think you've found it then you can test continuity of the fuse and replace if necessary.…

view full answer...

Answer 6

The Replacement Control Unit for Kwikee Electric RV Steps #LC379146 which is part 90950600 you referenced is does not have a specific wiring diagram, but I've attached the closest thing and have also included a video of an installation to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Control Unit for Kwikee Steps Part 094707-04-700

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching