Does the Square Pipe Mount Swivel Jack TJDP-7000S-B Come with the Weld On Mount

Question

Question:

Looking to buy 4 ea of the lift jack TJDP-70005-B. Does each come with the weld on female portion that swivels.

asked by: Paul E

0

Expert Reply:

The Square Pipe Mount Swivel Jack w Footplate part # TJDP-7000S-B does indeed come with the pipe mount that gets welded to the trailer frame that the jack gets attached to and swivels on.

expert reply by: Conner L

0

Answer 1

The end that normally attaches to jack #TJDP-7000S-B is #TJP-OP58. It has an outer diameter of 2-1/2 inches and inner diameter of 2 inches. For a weld-on male end that has 5/8 inch pin holes to match the above female mount use #BD015279.

view full answer...

Answer 2

Yes the pipe diameters of the #BDPG9810-00 and the #TJDP-7000S-B are the same. Both of them have a 2 inch inner diameter and a 2-1/2 inch outer diameter.

view full answer...

Answer 3

The Square Direct Weld Jack #TJD-7000S does not include a mount and is designed to be welded directly to your trailer. For a similar jack the Square Pipe Mount Swivel Jack #TJDP-7000S-B installs using a weld-on pipe mount. It meets the same 7,000…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Does the Square Pipe Mount Swivel Jack TJDP-7000S-B Come with the Weld On Mount

Product Page this Question was Asked From

Continue Researching