Amp Draw Of Buyers Ultra Bright LED Flood Light

Question

Question:

looking to get the amp draw on this

asked by: Scott

0

Expert Reply:

The Ultra Bright LED Flood Light part # 3371492196 is a 75 watt LED light. If its wired to a 12V system the amp draw is 6.25 amps. If its wired to a 24V system the amp draw is 3 amps. LED lights draw a very small amount of power compared to incandescent lights.

expert reply by: Heather A

0

Answer 1

I am not sure which flood light that you are referring to but if you know the type and wattage rating of the bulb then you can get a good idea of the lumen output. The Optronics Halogen Utility Light part #QH16CTS for example contains a 35 watt…

view full answer...

Answer 2

I spoke with someone from Buyers Products about your issue. They suggested that running the Ultra Bright LED Flood Light - 9,000 Lumens - Black Aluminum - Clear Lens - 12V/24V, part #3371492196, to your battery will solve your problem. There is not…

view full answer...

Answer 3

I recommend the Buyers Products Ultra Bright LED Flood Light in either 4,050 Lumens #3371492190 or 9,000 Lumens #3371492196, to replace the halogen lights on your Haulmark Race Enclosed Trailer. You will want to verify the fitment for these as I am…

view full answer...

Answer 4

The Buyers Products #3371492196 LED flood light does not have a built-in on/off switch. I would use the Seaflo #SE29VR Battery Disconnect switch for my outdoor switch, then to avoid drilling I would pick up some 3M heavy duty automotive mounting tape…

view full answer...

Answer 5

Hey there Dylan, I had a coworker go out to the warehouse to measure the bracket on the Ultra Bright LED Flood Light - 4,050 Lumens - Black Aluminum - Clear Lens - 12V/24V #3371492190. It measures 2" wide (left to right) and 1" deep (front…

view full answer...

Answer 6

Yes The Ultra Bright LED Flood Light #3371492196 can be used as a backup light when connecting to your reverse blue wire from the 7 plug, but you need to make sure that the circuit can handle the power of the light. Each light runs 6.25 amps, since…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey William, so the 3 inch hitches do use the larger hitch pin diameter but the 2-1/2 inch hitches still use the smaller one. So with a reducer like the part #38735 technically you would use both sizes. If you check out the picture I attached you can…

view full answer...

Amp Draw Of Buyers Ultra Bright LED Flood Light

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching