Where Exactly to Install Pacer Performance PP20-702 3rd Brake Light Logic Module

Question

Question:

Where is the best place to mount the unit inside the camper cap or under the truck by the spare tire. And is it weather proof.

asked by: Richard S

0

Expert Reply:

The module is weather proof according to the manufacturer but I'd recommend installing it so that it's as well protected as possible. Inside the camper shell would be ideal as the 3rd brake lamp wiring is easy to access there.

expert reply by: Mike L

0

Answer 1

The functions for a 4-way trailer wiring is left turn, right turn, running lights, and ground. There is no 12V wire on a 4-way trailer connector. If you are talking about a 7-way trailer connector here are the suggested wire gauges: Right turn, left…

view full answer...

Answer 2

The best product we have for wiring third brake lights in a camper shell is the 3rd Brake Light Logic Module part #PP20-702. If you were to combine this with an in-bed wiring harness such as the Curt 5th Wheel/Gooseneck Custom Wiring Harness part…

view full answer...

Answer 3

Thanks for the picture! The 3rd Brake Light Logic Module item #PP20-702 you were looking at is exactly what you need to activate a third brake light on your 2022 Ford F-150's Overland camper topper. Once connected, this module allows the third…

view full answer...

Answer 4

In most cases when this occurs, it's down to the wiring being connected to the wrong spots on the 7 way trailer plug. You'll want to be sure you're using the 3 o'clock and 9 o'clock pins when looking at the back of the plug.…

view full answer...

Answer 5

I understand your frustration with wiring the 3rd Brake Light Logic Module, part #PP20-702. The wiring diagram provided is not very comprehensive. While we do not have another diagram to send, I can explain this in clearer terms. The module is meant…

view full answer...

Answer 6

The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module #PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light. If there is a specific light style that you are…

view full answer...

Answer 7

The wiring system of the 2016 Ford F-150 has a combined tail light wiring system. The turn signals and brake lights are on the same circuit. Since the light bar is wired to the combined lighting system the turn signals illuminate when you press the…

view full answer...

Answer 8

I do have an option for you that will allow you to not have to splice into your taillights, but we do not have a product that is similar to the Leer 300200 harness. The Tekonsha T-One Vehicle Wiring Harness #118384 will connect in line of the factory…

view full answer...

Answer 9

The 3rd Brake Light Logic Module part #PP20-702 is what we recommend and use when powering the third brake light on a camper shell as it's designed for this exact purpose. There are two input wires (both yellow) in which you'll attach the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Where Exactly to Install Pacer Performance PP20-702 3rd Brake Light Logic Module

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching