Can the Optronics Flexible LED Light Strip Be Cut With New Ends Put On

Question

Question:

I am trying to light up side boxes on a fire truck I only need about 5 foot of lights per side box can I cut your strip lights an put another end on the piece I cut of?

asked by: Duane H

0

Expert Reply:

Yes, the Optronics Flexible LED Light Strip part # UCL90CB can be cut to the desired length you need for your application. That said, there are cut lines on the strip you must use which are located every 2". Once the cut is made you can then use the Optronics LED Light Strip 12-Volt Connector with Wire Leads part # A90PB to make your connections.

expert reply by: Conner L

0

Answer 1

Hey Brian we used to carry the connector part number A90P1B that was used to connect different sections of the Optronics Flexible LED Light Strip #UCL90CB but at this time we can't get it anymore. If instead you were wanting to have three…

view full answer...

Answer 2

Yes the Optronics Flexible LED Light Strip #UCL90CB would replace your Carefree LED lights and would splice right to the same wiring of what you have now.

view full answer...

Answer 3

The number you provided from the lens, SAEAP2 16 DOT states that the lens is compliant with DOT regulations, but in most cases it won't help us identify the lens. However, we've gotten enough inquiries about this lens that I can identify the…

view full answer...

Answer 4

The lenses on clearance lights are not generally removable as they are often "sonically sealed" such as the Optronics Trailer Clearance or Side Marker Light #MC57AB; this means they are submersible. Instead of buying a light and taking the…

view full answer...

Answer 5

In regards to using the Optronics LED Light Strip 12-Volt Connector with Wire Leads part #A90PB with the Optronics Flexible LED Light Strips like part #UCL90CB, you'll need to make sure of two things. The first is that you are removing the double…

view full answer...

Answer 6

Hey Jesse! If it's just the LED light strip that's peeling off, then I recommend picking up some strong adhesive double-sided take and securing it back in place with that, but if you're talking about the "bar" that the light…

view full answer...

Answer 7

Thanks for the picture! The Optronics Flexible LED Light Strip item #UCL90CB is extremely versatile. It will connect to any 12-volt power source so I am sure whatever power source and switch your lights are currently running off of will work with…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can the Optronics Flexible LED Light Strip Be Cut With New Ends Put On

Product Page this Question was Asked From

Continue Researching