Replacement Kingpins for Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes

Question

Question:

Where do I get or how do I order the kingpins for my dolly

asked by: Robert J

0

Expert Reply:

The replacement axle assemblies and kingpins for the Roadmaster Tow Dolly # RM-2000-1 (DISCONTINUED) can be found as part # RM-9210071-91 for the driver's side and part # RM-9210072-92 for the passenger's side. When you replace the kingpin assemblies you have to replace the axle part as well which you can see in the attached cutout from the instructions and why these part numbers are labeled as such.

expert reply by: Jon G

0

click to enlarge

Answer 1

The Thule Tepui Low-Pro 2 Rooftop Tent part #TH8001LP204 doesn't come with an annex and there is not one for this. The Yakima SkyRise HD Tent for Roof Rack Crossbars part #Y07436 doesn't come with an annex either but there is an option to add…

view full answer...

Answer 2

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS #DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not…

view full answer...

Answer 3

You will want the Replacement Passenger Side Fender for Roadmaster Tow Dolly 2000-1, #RM-921003, for your Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2050-1. The Replacement Driver's Side Fender for…

view full answer...

Answer 4

According to Roadmaster, a tow dolly like the Roadmaster #RM-2050-1 has a tongue weight of roughly 80-lbs because of the way it was engineered. If you've got a different brand of tow dolly, you will want to use a tongue weight scale like the…

view full answer...

Answer 5

Because the front axle of the towed vehicle sits over the axle of the tow dolly, very little weight is transferred to the tongue of the tow dolly. I spoke with my contact at Roadmaster and he said the Roadmaster Tow Dolly, #RM-2050-1, was engineered…

view full answer...

Answer 6

In order to replace the king pins on the Roadmaster Tow Dolly part RM-2000-1 (Discontinued) you must obtain the Replacement Axle Assembly and King Pin Kit for Roadmaster Tow Dolly part #RM-9210071-91 for driver side or part #RM-9210072-92 for…

view full answer...

Answer 7

I spoke with my contact at Roadmaster and he said it sounds like you need to do an alignment on your Tow Dolly part #RM-2050-1. He said it sounds like the setup is toe-out and needs to be corrected. I attached a picture that I took from the attached…

view full answer...

Answer 8

They actually are the same dolly. Roadmaster has two part numbers for the electric tow dolly; the part #RM-2050-1 we have it listed as and the part RM3477.

view full answer...

Answer 9

I was able to confirm that the diameter of both the Replacement Steering Pin and Clip #RM-357100-00 and your Master Tow tow dolly are both 5/8" in diameter. You will be able to use the Roadmaster Pin on your Master Tow dolly.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Kingpins for Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes

Continue Researching