Recommended Cover for Rpod 191 with Thule Awning

Question

Question:

What cover do you recommend for an Rpod 191 with the Thule awning, for snow/sun protection in Montana? Thanks

asked by: Tanya

0

Expert Reply:

The best option for a storage cover for your R-Pod 191 is going to be the Classic Accessories PolyPRO 3 # CA80-197-171001-00 as it's the correct size and offers the best protection in all climates like where you'll be in Montana that has a lot of snow and sun. This will easily fit with the Thule awning you have as well.

expert reply by: Jameson C

0

Answer 1

The correct storage cover for a Forest River R-Pod 190 is the Classic Accessories PolyPro III Deluxe RV Cover for R-Pod part #CA80200. This cover is designed to conform to the exact shape of your trailer for a tight, custom like fit. It has zippered…

view full answer...

Answer 2

Yes, RV storage covers like the Classic Accessories PolyPro III Deluxe RV Cover for R-Pod Trailers #CA80-197-171001-00 do take into account for AC units and other accessories being on the roof. I was actually just looking at a similar cover from…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Rob, for your 2021 Jeep Grand Cherokee I would recommend the Prodigy P3 part #TK28ER which comes with a custom fit harness designed for your Grand Cherokee. The P3 is the nicest controller around due to how easy it is to use and setup and how…

view full answer...

Answer 5

Since your 2020 R-Pod 191 has a 3,500 lb Lippert axle the correct lift kit you'd need is the part #LC270682 which will give it a 3-1/2 inch lift.

view full answer...

Answer 6

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Recommended Cover for Rpod 191 with Thule Awning

Product Page this Question was Asked From

Continue Researching