Front Air Bags for 2004 Workhorse P32 Chassis

Question

Question:

What part number would I need for the front airbag on a 200 a 2004 Workhorse P32 chassis

asked by: Ginger S

0

Expert Reply:

For the front axle of your 2004 Workhorse P32 chassis the correct air bag kit is the Air Lift 1000 Air Helper Springs # AL81560. This includes both air springs and the hardware to install them. If you need just a single air bag by itself you can use part # AL81260. These springs provide a combined load-leveling capacity of 1,000 pounds and will do a great job of stabilizing your ride.

I attached an image a customer submitted of the air spring and you can even see on the top where the printed numbers match the picture you submitted.

expert reply by: Chris R

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

If your 2003 Workhorse RV is a P series P30 or P32 or the W18 series you'd want the Air Lift #AL81560.

view full answer...

Answer 5

The front Firestone Coil-Rite Air Helper Springs #F4100 is the correct kit for a 1994 Chevy Class A chassis (should be the P-30) you have for your Winnebago motorhome! If you're looking for rear air bags as well then you need one of the following…

view full answer...

Answer 6

You can install AC units on pop ups like what you have. For that a kit like the Advent Air part #ACM135C would be a great option. It comes with a 13.5k BTU unit, a manual air distribution box, and a capacitor to make it easier on power consumption.…

view full answer...

Answer 7

For front air bags that fit inside of the coil springs on your 2002 Workhorse P32 chassis you will need #AL81560. You can roll up these bags and insert them up from the bottom through the hole below the coil spring mounts that you have described. No…

view full answer...

Answer 8

For the 1-1/4 inch factory front anti-sway bar on the 1995 Chevy P30 chassis you can use Roadmaster Polyurethane Bushing Kit #RM-4109-109. If you wanted to replace the factory front sway bar with a beefier, more effective model you can use…

view full answer...

Answer 9

For the Workhorse W42 chassis we have the Timbren rear suspension kit part #TGMRP30 but we don't have any air spring solutions. The Timbren kits offer the same support without requiring you to worry about air pressure and leaks though.

view full answer...

Answer 10

The Air Lift Kit part #AL81560 that you referenced is the correct air bag kit for the front springs of your 2000 Workhorse P30 chassis that your Itasca Sunrise is built on. You would need to remove what is there now and install these in place of…

view full answer...

Front Air Bags for 2004 Workhorse P32 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching