Does the Dutton-Lainson Quick Disconnect Winch Harness # DL24151 Include Both Male and Female Ends

Question

Question:

Does this winch wiring come with male and female quick disconnects at the rear of the vehicle? The picture shows just one. Thank you for your time.

asked by: Mark S

0

Expert Reply:

The Quick Disconnect Wiring Harness you mention, part # DL24151 is designed to plug directly into the winch, as shown in the photo I produced for you.

According to the instructions, the wiring harness is meant to be unplugged and stowed in the tow vehicle when not in use. If you wanted to construct a quick disconnect jumper, you could do so by using part # DL24085 and the appropriate length of 8 gauge wire. The plugs would be installed on both ends of your jumper, which could be used to connect the winch to the wiring on the vehicle.

expert reply by: Mike L

0

click to enlarge

Answer 1

I have exactly what you need for your boat trailer. For this, I recommend using the Dutton-Lainson StrongArm Electric Winch part #DL25532 if you have roller bunks or part #DL25010 if you have standard wooden bunks. The roller bunks will aid getting…

view full answer...

Answer 2

They sure will! The following components you were looking at will all work perfectly with your new 2023 Yamaha SX190 Jet Boat: Strong Arm Winch #DL25010 Quick Disconnect Connectors #DL24085 Winch Cover #DL24051 With that said you shouldn't need…

view full answer...

Answer 3

Winch makers usually provide guidance about the required power to operate their winches to their fullest capacity. For example, the 3000-lb-rated Dutton-Lainson StrongArm Electric Winch #DL25010 will require 70-amps of battery current to deliver its…

view full answer...

Answer 4

I am glad to hear you have enjoyed your Dutton-Lainson StrongArm winch. It is a quality product. The circuit breaker you are looking for is part ##DL304025. This is the 80 Amp replacement fuse for the Dutton-Lainson StrongArm Winch Wiring Harness. I…

view full answer...

Answer 5

The cable is 25 feet long (the ground wire is 8 feet long). The harness is constructed of 8 gauge wire. This harness also provides an 80-amp circuit breaker. I have also included a link to our FAQ article on the different ways to wire a winch.

view full answer...

Answer 6

When installing the Dutton-Lainson Wiring Harness for DC StrongArm Electric Winches #DL24151. The ring terminal with the circuit breakers on it will attach to the positive post on the battery and the wire with just the ring terminal will attach to…

view full answer...

Answer 7

I spoke to Dutton-Lainson and there is replacement wiring for the StrongArm Electric Trailer Winch - Marine - 1,500 lbs #TW4015. The Wiring Harness for DC StrongArm Electric Winches #DL24151 will be a direct replacement, or addition in your case.

view full answer...

Answer 8

The TW9000 winch does require the use of the 80 amp Replacement Circuit Breaker for DL StrongArm Winch Wiring Harness #DL304025. These are thermal breakers so they can be reset.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Does the Dutton-Lainson Quick Disconnect Winch Harness # DL24151 Include Both Male and Female Ends

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching