Replacement Slow Blow Fuse for Ultra-Fab Electric A-Frame Jack 3502 Model

Question

Question:

I recently had my campers electric tongue jack replaced with: an Ultra 3502. I like to have things on hand that I may need before I actually need them, such as fuses. Camping World doesnt have the slow blow fuses in stock nor have I been able to find them anyplace around me so far. How can I order these fuses for back up , just in case. Ive had bad experiences with fuses blowing in the previous electric jack and dont want to get stuck in this situation again. Any guidance would be appreciated.

asked by: Priscilla D

0

Expert Reply:

The correct replacement slow blow fuse for the Ultra-Fab Electric A-Frame Jack (3502 Model) part # UF38-944017 is the Replacement 30-Amp Slow Blow Fuse part # UF38-751034. Some other parts you may want to keep on hand are the Replacement 20-Amp Auto-Reset Circuit Breaker part # UF38-101238 and the Replacement Toggle Motor Switch part # UF38-75-1037.

expert reply by: Conner L

0

Answer 1

Phoenix Electric Trailer Jack - A-Frame - 22-1/2" Lift - 4,000 lbs #UF38-944040 sounds like it needs a better ground connection. You can wire it directly to the battery like in the installed video or you can install the ground wired to the…

view full answer...

Answer 2

Yes, John we sure do! To replace the fuses in your FanTastic Vent Fan you will need the Replacement 4 Amp Slow Burn Fuse Kit for Fantastic Fans item #DMC57FR you were looking at. This comes with two fuses that measure 1-1/4" x 1/4". The…

view full answer...

Answer 3

I spoke with my contact at MaxxAir regarding the MaxxAir 2 Vent Covers like the Smoke #MA00-933073 that you were looking at and the Standard Covers like #MA00-933067. He said there are two primary differences between the two models. The first is that…

view full answer...

Answer 4

The plastic housing of the Fan-Tastic Vent Roof Vent w/ 12V Fan #FV802250 is very sturdy and would hold up well. I'd recommend using a Fan-Tastic roof vent cover like the #DMC38FR instead though as this was designed specifically for use with the…

view full answer...

Answer 5

The model number for a Fan-Tastic RV roof vent is often found on a sticker on the top side of the fan, so you may have to carefully traverse to the top of your RV roof and open up the lid to find it. Here are the options for an Ultra-Breeze vent…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Replacement Slow Blow Fuse for Ultra-Fab Electric A-Frame Jack 3502 Model

Continue Researching