Width of CE Smith U-Bolt # CE15251A

Question

Question:

question is the inside bolt to inside bolt dimension 2.125 alowing it to fit over a 2 by 3 box frame

asked by: Richard J

1

Helpful Expert Reply:

I went out to our warehouse to take a look at the CE Smith U-Bolt # CE15251A and found that the listed 2-1/8" (2.125") width is indeed from the inside of one bolt to the inside of the other. This will fit over a 2" x 3" box frame.

I have attached a diagram to assist.

expert reply by: Chris R

1

Answer 1

For starters, in order to use the CE Smith Self Centering Keel Roller for Boat Trailers part #CE29505 on your boat trailer you will also need to use the CE Smith Panel Bracket for 12" Boat Trailer Rollers part #CE10305G and the Roller Shaft with…

view full answer...

Answer 2

I have a few options to help with loading the boat on the trailer but the best would have to be the CE Smith Keel Roller for Boat Trailers part #CE29505. In order to mount them you'd need the Roller Shaft with Pal Nuts part #CE10727A and CE Smith…

view full answer...

Answer 3

To mount the CE Smith Panel Bracket for 12" Boat Trailer Rollers - Galvanized Steel #CE10305G you were looking at you have two options. The first being welding the bracket to your trailer. If you go this route you need to make sure to sand off…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Width of CE Smith U-Bolt # CE15251A

Product Page this Question was Asked From

Continue Researching