Grease Seal Replacement for Dexter 5,200 lb Axle

Question

Question:

What is the correct part number for the grease seals for my Dexter 5200 axles? Dexter axle # 6421250 Serial # 132103386

asked by: William B

0

Expert Reply:

For a Dexter 5,200 lb axle the correct grease seal is the part # GS-2250DL that you referenced which has an inner diameter of 2.25 inch and an outer diameter of 3.376 inch.

expert reply by: Jameson C

0

Answer 1

The D52 on your axle tag means it is a 5,200 lb axle. For a kit that has all of the bearings and seal for your Dexter D52 5,200 lb axle you'd want the kit part #BK3-310 and then for a spindle nut you'd want the #165686. Aside from that the…

view full answer...

Answer 2

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 3

Generally speaking, there is no need to apply a gasket maker on the outside of a grease seal prior to installing it in the hub. This is not really common practice nor have I ever seen any issues not doing so. That said, I am aware there are certain…

view full answer...

Answer 4

You can use the other components you remove from your hubs. After you have removed the hub components you will want to inspect all of the parts and replace if you find any discoloration or signs of wear or damage such as a nick. On the race you can…

view full answer...

Answer 5

The closest seal that we have to the 3.38" OD and 2.11" ID of your grease seal is part #GS-2125DL which has a 3.376" OD and a 2.125" ID. This is designed for Dexter 5,200 lb - 7,000 lb axles and the seal cross-reference number is…

view full answer...

Answer 6

I do have a hub and bearing assembly that will allow you to replace the hubs on your mobile home axle however, mobile home axles are intended for a one time single use only, therefore there is a limitation to readily available replacement parts. When…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Grease Seal Replacement for Dexter 5,200 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching