Front Hitch for 2004 Jeep Wrangler that Installs Under Front Bumper

Question

Question:

Yes I just got my hitch today but I dont have a stock bumper so it wont work on the top of the bumpers .so I was wondering if there any way to but it under the jeep 2004 tj thanks

asked by: Rick M

1

Helpful Expert Reply:

For your 2004 Jeep Wrangler TJ we have a front hitch that's designed to fit underneath the front bumper with the Curt # C31028 which would be your best option, but there isn't a way to mount a # 31408 on top of the bumper that you have.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The CURT Front Hitch, #31408, attaches to the top of the front bumper on your 2004 Jeep Wrangler. I have included a link to installation instructions and a photo of a similar hitch in the same mounting location for you. The front mount hitch makes a…

view full answer...

Answer 2

On the Rapid Hitch Adjustable Aluminum Ball Mount #AM3411 the ball can be removed from the mount by gently tapping on the mount when it is removed from the shank part. The ball pin is just a friction fit. If needed you can apply some light lubricant,…

view full answer...

Answer 3

Hey Jim, the only front hitch we have for your 2005 Jeep TJ that installs below the front bumper is the Curt part #C31028 but it does require drilling into the frame.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Front Hitch for 2004 Jeep Wrangler that Installs Under Front Bumper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching