Replacement Trailer Axle With 89 Inch Hub Flange To Hub Flange Measurement

Question

Question:

have a bent axle 80inch from leaf center to center 89inch axle hub flange to axle hub flange with 5 lug rims which measure 3.25inch from center of stud to center of stud and I cant seem to find a replacement on your wed site, can you help

asked by: Keith W

0

Expert Reply:

In order to replace your trailer axle you can use the Dexter Trailer Axle Beam with EZ-Lube Spindles part # T3584F-EZ-8974 for a 3,500 lb capacity, part # 8327820 for a 5,200 lb weight capacity, or part # 8327830 for a 6,000 lb weight capacity. These axles all have the correct hub face measurement but you will need to have the spring seats moved to match that of those on your trailer.

Based on the measurements that you provided of your stud centers, you have a 5 on 5-1/2" bolt pattern. Although we do not offer the above axles with a trailer hub that has a 5 on 5-1/2" bolt pattern, we do have what you need to add one I would just need you to first confirm what axle capacity you will be using and whether or not it has brakes.

expert reply by: Conner L

0

Steven

8/2/2020

I have a dexter axle with this number on the tag, 6951148. It also states HF 86.5, SC 68.5. Do you carry this part or can you get it? I only need the bare axle, i can transfer my components over. My current axle is bent.

Chris R.

8/11/2020

We do have some trailer axles available that match the 86-1/2" hub face length on your existing axle, but nothing that perfectly lines up with that 68-1/2" spring seat measurement, although those could potentially be cut off and re-welded to line up to your frame. I've attached this selection below.

Helpful Links

dept-pg-trailer_axles-sz-86~1%7c2_inch_long.aspx

Ronald R.

11/22/2021

@Steven I'm also looking for same bare axle.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Replacement Trailer Axle With 89 Inch Hub Flange To Hub Flange Measurement

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching