How to Use Circuit Tester to Find Brake Light Switch Wire for Brake Controller Installation

Question

Question:

In the article it states to refer to the video for the stop switch connection. I did not see a link for this video anywhere within the article. question 10200. Thanks

asked by: Bob B

0

Expert Reply:

The video you referenced in your question about trailer brake controller installation is linked for you. At the 7:20 mark our installer does begin the process of identifying the brake light switch wire that will connect to the brake controller's RED wire. He used a circuit tester like # PTW2992 and # PTW2993 to probe the wires at the brake light switch to find the one wire that carries 12V power ONLY when the pedal is pressed.

There will be other wires for other functions clustered in that same general location above the brake pedal, so it is important to test those wires to find the one that carries power only when the pedal is pressed. A wire's color is not a reliable way to determine the function carried on it.

expert reply by: Adam R

0

Answer 1

When you are hardwiring a trailer brake controller like the Prodigy P2 #90885 the red wire connection that provides the triggering signal to the controller should be made to the wire on the COLD SIDE of the brake light switch circuit. This is the…

view full answer...

Answer 2

Normally you can find the brake light switch under the dashboard at the top of the brake pedal. There could be a number of wires attached to the switch so you can use a tester like part #PTW2993 to test the wires. Since the auto manufacturers can use…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

How to Use Circuit Tester to Find Brake Light Switch Wire for Brake Controller Installation

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching