How To Transfer Weight Distribution System From a Truck To An SUV With Different Ground Clearances
Updated 06/11/2019 | Published 06/10/2019 >
Products Featured in This Question
Question:
I have two different tow vehicles and my SUV is significantly lower than my Ford F-350. I know I can replace the shank, however, I believe that would require that I remove the bolts and adjust anytime I switch vehicles. Unless, there are pins available that replace the bolts. Can I use High-Low Adapter to the weight distribution hitch when using my truck.
asked by: Mitch
Expert Reply:
I do have the correct options for you but the Roadmaster High-Low Adapter part # RM-076 cannot be used with a weight distribution system. Since you have two vehicles with very different ground clearances you will just need to have two shanks, one for the truck with more drop and one for the SUV with less drop. The good news is that most weight distribution shanks are pretty universal so all I would need from you is the drop needed for each vehicle. This can be found by subtracting the distance from the ground to the top, inside edge of the receiver tube from the distance from the ground to the bottom of the trailer coupler while level.
For example, the Curt Adjustable Weight Distribution Shank part # C17100 which has a 2" drop for a trunnion system could be used on your SUV and the Curt Adjustable Weight Distribution Shank part # 17120 which has 5-3/4" drop (for a trunnion system) could be used on your truck. You don't need to match the brand of the shank to the weight distribution system.
I have attached a list of shank options for you below once you find out how much rise/drop you need.
Product Page this Question was Asked From
Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 6" Rise/Drop - 6K GTW, 200 lbs TW
- Accessories and Parts
- Tow Bar
- Hitch Adapters
- High-Low Adapter
- Fits 2 Inch Hitch
- 6 Inch Rise/Drop
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: shank
- Q&A: Distance From Top of Curt Shank to Center of Topmost Adjustment Hole
- Video: Breaking Down the Curt Adjustable Weight Distribution Shank
- Video: Review of Xtreme Heaters RV Heaters - Small Boat RV Heater 400W - XH54FR
- Shop: Equal-i-zer Weight Dist Shank - 12" Long - 7" Rise, 3" Drop - 600 to 1,400 lbs TW
- Shop: Weight Distribution Shank for Gen-Y Hitch Adjustable Ball Mounts w/ 2" Receivers
- Shop: Curt Adjustable Weight Distribution Shank - 8"
- Q&A: Recommended 7 Hole 2" Shank for a Weight Distribution System
- Q&A: Troubleshooting Height Adjustment for Reese Weight Distribution System
- Q&A: Recommended Weight Distribution System with 5 Inch Rise for 2007 Toyota Sienna
- Q&A: Recommended Replacement Weight Distribution Shank for Curt TruTrack System
- Q&A: Will the Curt Adjustable Weight Distribution Shank Accept 3/4 Inch Diameter Bolts
- Q&A: Is Curt Weight Distribution Shank #17100 Compatible with Fastway Weight Distribution
- Search Results: weight distribution shank
- Search Results: equalizer hitch
- Search Results: equalizer shank
- Search Results: fastway
- Search Results: weight distribution hitch
- Search Results: husky shank
- Shop: Fastway Trailer Hitch Lock and Adjustment Pin Lock Set for Flash E Series HD Ball Mounts
- Shop: Equal-i-zer Weight Distribution w/ 4-Point Sway Control - No Shank - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Fastway e2 Weight Distribution Shank - 12" Long - 6-1/2" Rise, 4" Drop - 1,200 lbs TW
- Shop: Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch - 7.5K GTW, 750 lbs TW
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement

