Is the Bolt-Together Round Bar Head a Replacement for 2 Sway Ball Setup For 10,000lb Hitch?
Updated 06/02/2020 | Published 07/03/2018
Products Featured in This Question
Question:
I have a older setup and I just need to replace the hitch for one that has 2 sway ball setup for 10,000lb hitch is this the one I need?
asked by: Dominic S
Expert Reply:
The sway control ball on the Replacement Weight Distribution Bolt-Together Round Bar Head # PS58442 can be used with two balls and you can use the balls on either side of the head assembly (see picture).
This replacement head fits Pro Series weight distribution systems # PS49583, # PS49582, # PS49901
The adjustable shank # C17100 is not included with this product, but it does come with the bolts, the nuts and the washers to get that installed and attached to the weight distribution shank. Its also comes with a hitch pin and clip. This is to secure the weight distribution shank inside the receiver tip of your hitch. Its going to come with two other clips. These are for the frame brackets or lift brackets.
For an additional hitch ball with a 2 inch diameter and a 1-1/4 inch diameter shank i recommend part # A-90. If you need a 2-5/16" Hitch Ball with a 1-1/4" Diameter, I recommend # 63840.
Since you are going to use this head with 2 sway bars, you will need (2) Curt Sway Control Hitch Ball # C40093.
In order to make sure this unit works with your system, can you tell me what type of system you have? If you can send me a picture of the system that will help also.
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Recommended Friction Sway Control System For Dual Friction Setup
- Q&A: Recommendation for Adding 2nd Friction Sway Control Bar to Trailer
- Shop: Sway Control 2-Ball Platform for BulletProof Hitches Ball Mount - 2" and 2-5/16" Balls
- Shop: Replacement Head for Fastway e2 Weight Distribution Systems - Trunnion Bar
- Shop: Curt Replacement Weight Distribution Head for Trunnion Style Bars
- Shop: Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 10K
- Shop: Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 10K
- Search Results: gen y hitch
- Search Results: shank
- Q&A: Distance From Top of Curt Shank to Center of Topmost Adjustment Hole
- Video: Breaking Down the Curt Adjustable Weight Distribution Shank
- Video: Review of Xtreme Heaters RV Heaters - Small Boat RV Heater 400W - XH54FR
- Shop: Equal-i-zer Weight Dist Shank - 12" Long - 7" Rise, 3" Drop - 600 to 1,400 lbs TW
- Shop: Weight Distribution Shank for Gen-Y Hitch Adjustable Ball Mounts w/ 2" Receivers
- Search Results: weight distribution hitch
- Q&A: Troubleshooting Height Adjustment for Reese Weight Distribution System
- Q&A: Recommended Replacement Weight Distribution Shank for Curt TruTrack System
- Q&A: Recommended 7 Hole 2" Shank for a Weight Distribution System
- Q&A: Recommended Weight Distribution Shank for Low Ground Clearance
- Search Results: weight distribution shank
- Search Results: equalizer shank
- Search Results: accessories and parts
- Search Results: husky shank
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Shop: Brake Controller
on Accessories and Parts
Laverne S.
5/29/2020
I have a new Curt hitch don't know how to take off the round bars off the hitch when unhooking trailer from truck and also is there a problem with ii when backing up the trailer, Thanks